DOALL VERTICAL SAW Model 2012-VH Machine Capacity: 20" x 12" Throat, Band to Column: 20", Table Tilt 10 degree POS & 45 degree NEG

DOALL VERTICAL SAW Model 2012-VH Machine Capacity: 20" x 12" Throat, Band to Column: 20", Table Tilt 10 degree POS & 45 degree NEG
Table Capacity: 500 lbs
Column Mounted Controls

Column mounted controls give the operator easy access to
band start and blade speed insuring their hands are away
from the blade at band start.

Variable Frequency Band Drive
Band drive is comprised of an electric variable frequency
drive controlled motor transferring power thru our time
honored, gear driven, two speed transmission giving
maximum torque to the tooth tips of the saw blade reducing
band stall and tooth strippage.

Post Elevating Handwheel
Easy to operate post elevating handwheel allows the
operator to keep the upper saw guide block as close to the
top of the material being cut without getting their hands
close to the blade during adjustment. Proper positioning
minimizes the possibility of band deflection increasing band
life and safety.

Bandwheels
Flanged, cast aluminum, tapered bandwheels are supplied
with rubber tires to minimize wheel wear and allow for the
use of only one set of saw guide blocks for bands 1/16" thru
1". The carbide backup bearing coupled with the wheel
flanges support the back of the band during the cut
decreasing band fatigue and increasing band life.

Manual Band Tension
Proper blade tension is manually set to a factory installed
indicator which covers all widths of saw bands. This indicator
will prevent the possibility of over/under tightening of the
sawband for maximum cutting rates and extended band life.

Cast Steel Table
Hydraulically driven cast steel table with 12" of travel has
two "T" slots for ease of clamping of fixturing or parts
eliminates the possibility of movement during the cut

Wheel Brush
Column mounted controls give the operator easy access to
band start and blade speed insuring their hands are away
from the blade at band start.
A strategically mounted replaceable nylon wheel brush cleans
the surface of the lower wheel minimizing damage to the
lower wheel tire by reducing any chip buildup which may cause
improper blade tracking.

Saw Guide
Machine is equipped with one set of DoALL invented chevron
type saw guide blocks and inserts which will handle 1/8-1”
sawbands. These will allow proper support to the side and back
of the band minimizing deflection due to overfeed conditions.

Safety Systems
A unique transmission lock out system prevents shifting
between high and low speed while the band is running.
Preventing gear stripping and shiftfork damage.
Band door interlocks prevents the starting of the saw band
while the doors are open. They will also stop the band drive if
the doors open during operation which protects the operator
from being exposed to a moving band.

Feed Control
Hydraulic table feed control combines feed rate with feed force
allowing the operator to not only adjust table speed but
also adjust the force being applied to the blade maximizing
band life.
Optional ten-year warranty is available.

• Table tilt to 45 degrees negative - 10 degrees positive.
• Hydraulic reservoir
• Table 26-1/2 x 33-1/2 in. (673 x 851 mm)
• Manual band tension with indicator.
• Two T-Slots 1/2 in. (13 mm)
• Post elevating hand wheel.
• 20" Aluminum flanged, tapered bandwheels with rubber tires
• Chip box
• Chip blower (plant air required)
• Upper wheel adjustment 3"
• Saw blade guards.
• Operator controls mounted on column.
• Band door interlocks.
• One set of saw guide blocks with carbide backup for bands 1/8" to 1"
• Operation and parts manuals on USB stick.
• Recommended job selector
• One set of metal saw guide inserts for bands 1/4", 3/8",
1/2", 3/4", and 1" • Insert setting gages with wrench and trunnion wrench
• One (1) complimentary DoALL Bi Metal saw blade.
• Band wheel brush
• Variable frequency band drive.
• Work light